What Is YGM Grinding Mill? Advantages, Applications & Selection Guide For Mining Industry

1. Overview of YGM Grinding Mill
The YGM grinding mill, also known as YGM high pressure Raymond mill, is an upgraded and optimized grinding equipment developed on the basis of traditional Raymond mill, integrating high-pressure spring technology and suspension roller grinding principle. As a core equipment in the non-metallic ore powder processing industry, it is mainly used for fine grinding of various non-flammable and non-explosive mineral materials with Mohs hardness not exceeding 9.3 and humidity below 6%.
Different from ordinary grinding mills, the YGM grinding mill is equipped with a high-pressure spring system on the grinding roller assembly, which increases the rolling pressure between the grinding roller and the grinding ring by 1.2-1.4 times without increasing the motor power, thus significantly improving the grinding efficiency and finished product fineness. The finished product fineness of the YGM grinding mill can be flexibly adjusted between 80-600 mesh, and the qualified screening rate can reach 99%, which is difficult to achieve by other ordinary grinding equipment.
Mascot’s YGM grinding mill covers a complete range of models, including YGM65, YGM75, YGM85, YGM95, YGM130, YGM160, etc., with a production capacity ranging from 0.4t/h to 16t/h, which can meet the different processing needs of small, medium and large mining projects. It is widely used in mining, building materials, chemical industry, metallurgy and other fields, and is an ideal equipment for processing limestone, calcite, barite, talc, kaolin, quartz, feldspar and other mineral materials into fine powder.

2. Core Advantages of Mascot YGM Grinding Mill
As a professional manufacturer with rich experience in mining equipment R & D and production, Mascot optimizes the structure and performance of YGM grinding mill in combination with market demand and practical application scenarios, making it have obvious advantages compared with traditional grinding equipment and other brands’ products:

2.1 High Efficiency and Energy Saving
The YGM grinding mill adopts a high-pressure spring design, which enhances the grinding pressure between the roller and the ring, making the grinding efficiency 20% higher than that of the traditional Raymond mill under the same power condition. At the same time, the equipment adopts an optimized air circulation system and frequency conversion control technology, which can adjust the operation parameters according to the material characteristics, effectively reducing power consumption and energy waste. Compared with similar products, Mascot’s YGM grinding mill can save 15%-25% of energy, greatly reducing the production cost of users.

2.2 Stable Performance and Long Service Life
The key components of the YGM grinding mill, such as grinding roller, grinding ring and shovel, are made of high-strength wear-resistant materials, which have strong wear resistance and corrosion resistance, and effectively extend the service life of the equipment. The connection between the grinding unit and the upper classifier adopts a spring soft connection and soft belt sealing design, which reduces equipment vibration and noise, avoids resonance, and ensures stable operation of the equipment for a long time. In addition, the central shaft of the main engine adopts a new protective structure, which prevents the shaft from being worn, and the replacement of the oil seal does not need to disassemble the main engine, saving maintenance time and labor intensity.

2.3 High Fineness and Uniformity of Finished Products
The YGM grinding mill is equipped with a high-precision fineness analyzer, which can flexibly adjust the finished product fineness according to user needs, and the adjustment range is 80-600 mesh (some materials can reach 2000 mesh). The closed air circulation system ensures that the grinding process is carried out in a sealed environment, avoiding the pollution of materials and ensuring the high purity of finished products. The qualified screening rate of finished products is as high as 99%, which can well meet the material requirements of various industrial fields such as building materials, chemicals and ceramics.

2.4 Compact Structure and Easy Operation
The YGM grinding mill adopts an integrated three-dimensional structure, which occupies a small area and has strong integration, forming an independent production system from raw material feeding to finished product collection, which is convenient for on-site installation and layout. The equipment is equipped with an automatic control system, which has a high degree of automation, simple operation and easy mastery, and can reduce the labor intensity of operators. At the same time, the equipment is easy to maintain, and the daily maintenance work is simple, which reduces the maintenance cost of users.

3. Practical Application Cases of YGM Grinding Mill
Mascot’s YGM grinding mill has been widely used in various mining processing projects at home and abroad, and has won unanimous praise from users with its stable performance and high efficiency. The following are two typical application cases for your reference:

3.1 Kaolin Processing Project in Hubei, China
Project Background: A local influential kaolin processing enterprise in Hubei needed to process kaolin into 250-mesh fine powder for the production of ceramic raw materials. The enterprise initially used traditional grinding equipment, which had problems such as low efficiency, uneven fineness of finished products and high energy consumption, which could not meet the production needs.
Equipment Configuration: After on-site investigation and demand analysis, Mascot provided the enterprise with 2 sets of YGM95 high-pressure grinding mills, matching jaw crushers, bucket elevators, vibrating feeders and other auxiliary equipment to form a complete kaolin grinding production line.
Application Effect: Since the equipment was put into use, it has operated stably for a long time, with a daily output of 80 tons, which is 30% higher than that of the original equipment. The fineness of the finished kaolin powder is uniform, the purity is high, and it fully meets the production requirements of ceramic raw materials. At the same time, the energy consumption per ton of powder is reduced by 20%, and the production cost of the enterprise is greatly reduced. The enterprise has become a local model customer of kaolin processing.

3.2 Talc Processing Project in Inner Mongolia, China
Project Background: A talc processing plant in Inner Mongolia needed to upgrade its production equipment. The original traditional Raymond mill had problems such as large noise, serious dust pollution and low production efficiency, which did not meet the environmental protection requirements and production needs.
Equipment Configuration: Mascot provided the plant with 1 set of YGM130 high-pressure grinding mill, which is matched with a high-efficiency pulse dust collector to realize green and clean production.
Application Effect: After the equipment is put into use, the production efficiency is increased by 25%, the finished talc powder reaches 325 mesh, and the screening rate is 99%. The closed dust collection system effectively controls dust leakage, the noise is reduced to below 75 decibels, and it fully meets the national environmental protection standards. The plant's production capacity and product quality have been significantly improved, and the economic benefits have been greatly increased.

4. Related Product Recommendations
In addition to the YGM grinding mill, Mascot also provides a series of supporting mining grinding equipment to meet the different processing needs of users. The following are related product recommendations that can be matched with the YGM grinding mill:

4.1 Raymond Mill Plant
Mascot’s Raymond Mill Plant is a complete set of grinding production line equipment, which can be matched with YGM grinding mill to realize automatic feeding, grinding, grading and collection. It is suitable for large-scale mineral powder processing projects, with high production efficiency, stable operation and easy management. It is widely used in limestone, calcite, barite and other non-metallic ore processing fields.

4.2 Ceramic Ball Mill
The Ceramic Ball Mill is a high-purity grinding equipment independently developed by Mascot, which is suitable for fine grinding of high-purity materials such as ceramic raw materials, quartz and kaolin. It adopts ceramic lining and ceramic grinding media, which can avoid metal pollution of materials, and is especially suitable for occasions with high requirements on the purity of finished products. It can be used in conjunction with YGM grinding mill to realize multi-stage grinding and improve the fineness of finished products.

4.3 High-Pressure Suspension Grinding Mill
The High-Pressure Suspension Grinding Mill is an upgraded product of the YGM grinding mill, which has higher grinding efficiency and finer finished product fineness. It is suitable for ultra-fine grinding of non-metallic ores, with a finished product fineness of up to 2000 mesh, which can meet the high-precision processing needs of chemical, pharmaceutical, food and other industries.

5. Frequently Asked Questions (FAQs) About YGM Grinding Mill
We have sorted out 3 common questions about YGM grinding mill based on user feedback and practical application experience, hoping to help you better understand and use the equipment:

Q1: What materials can the YGM grinding mill process? What are the requirements for materials?
A1: The YGM grinding mill is mainly used for processing non-flammable and non-explosive mineral materials with Mohs hardness not exceeding 9.3 and humidity below 6%. Common processed materials include limestone, calcite, barite, talc, kaolin, quartz, feldspar, dolomite, gypsum, slag, etc. It should be noted that the maximum feeding size of the YGM grinding mill is 15-35mm (different models have different requirements), so the raw materials need to be crushed to the specified size by a crusher before grinding to ensure the normal operation of the equipment and the grinding effect.

Q2: How to adjust the fineness of the finished product of the YGM grinding mill? Is it easy to operate?
A2: The fineness of the finished product of the YGM grinding mill is adjusted by adjusting the rotating speed of the fineness analyzer. The higher the rotating speed of the analyzer, the finer the finished product; the lower the rotating speed, the coarser the finished product. The adjustment process is simple and convenient, and the operator can adjust it according to the production needs through the control panel without disassembling the equipment. At the same time, Mascot will provide professional operation training for users to ensure that operators can master the adjustment method proficiently.

Q3: What is the service life of the YGM grinding mill? What after-sales services does Mascot provide?
A3: The service life of the YGM grinding mill is related to the use environment, material characteristics and daily maintenance. Under normal use and standard maintenance, the service life of the main body of the equipment can reach 8-10 years, and the vulnerable parts such as grinding roller and grinding ring can be replaced regularly according to the wear condition, which is convenient and quick. Mascot provides a one-year quality guarantee period for the YGM grinding mill. During the guarantee period, if there is a quality problem with the equipment, we will provide free maintenance and replacement of vulnerable parts. In addition, we also provide 24-hour technical support, on-site installation and commissioning, operation training and other after-sales services to solve the worries of users in the process of use.

Zhengzhou Mascot Industry is a high-tech mining equipment company integrating R&D, manufacturing, sales, and after-sales service. Focusing on crushing, grinding, and mineral processing equipment, we provide professional solutions to our customers. We are ISO9001:2015 、certified, and our products include mobile crushing palnts, crawler crushing plant, construction waste crushing plants, jaw crushers, sand making machines, cone crushers, fine crushers, grinding mills, ball mills, etc., all with reliable performance to meet perse project needs.

Our advantages:

• Professional pre-sales support: Free project design and comprehensive solutions to help you accurately select the right equipment;

• Comprehensive on-site service: Providing installation guidance and worker training to ensure smooth equipment commissioning;

• Reliable after-sales guarantee: A complete after-sales system, timely response to technical inquiries and equipment maintenance, ensuring long-term stable operation.

To protect your rights, please contact us through the following official channels for professional service:

Official Website Customer Service

WhatsApp: 0086-18737119558

Email: mascot@mascotenv.com

We are committed to providing high-quality equipment and full-cycle services to deliver comprehensive intelligent solutions for the global mining industry!